096150 - Power Products: Traveller Series Inverter

Power-to-go

Features

High efficiency operation with precise regulation.
Input protection under conditions of under voltage, over voltage and over current.
Reverse polarity protection
Output protection under conditions of over current.
Over temperature protection to shutdown inverter under operating stress.

Protection
Traveller inverters are protected against over temperature, overload and over current. To maintain efficient safe operation, protection is also provided against battery under voltage and battery over voltage.

Operation Modes
Visual display monitors battery voltage and current draw. The bar graphs highlight the safe danger zones of operation providing an early warning system for voltage degradation and current overload.

Construction

Strong, classic aluminium housing anodised black.
Mounting feet for free standing.
Mounting flanges for more permanent placement.

Auto Start
Our model 096150 has the added feature of auto start. The inverter will automatically switch on and off with the operation of appliances to further conserve battery power.

Specifications

Model	096040	096075	066150
Input Voltage	11.0 - 15V DC	10.5 - 15V DC	10.5 - 15V DC
Rating Continuous	300W	600W	1200W
25 Minutes	350W	750W	1500W
5 Minutes	400W	875W	1750W
Surge	500W	1250W	2500W
Peak Efficiency	90%	90%	90%
Low Voltage Warning	10.7V DC	10.7V DC	10.7V DC
Low Voltage Shutdown	10.5V DC	10.5V DC	10.5V DC
Standby Current	25mA	N/A	10mA
No Load Current	25mA	0.6A	10mA
Demand Start Sensitivity	2W	N/A	2 - 10W
Output Frequency	50Hz	50Hz	50Hz
Output Wave Form	Modified Sine wave	Modified Sine wave	Modified Sine wave
Output Voltage	230V AC RMS±5%	230V AC RMS±5%	230V AC RMS±5%
Output Wiring	Dual Switched GPO's	Dual Switched GPO's	Dual Switched GPO's
Dimensions	228W x 115L x 66H mm	247W x 305L x 77H mm	247W x 450L x 77H mm
Weight	1.1Kg	3.7Kg	5.8Kg
Battery Leads	1.8 metre Lead with Lugs	1.8 metre Lead with Lugs	1.8 metre Lead with Lugs
Chassis	Anodised Aluminium	Anodised Aluminium	Anodised Aluminium

Rating @ 25° C Ambient & Nominal Battery Voltage

Operating Procedure

With no load connected to unit and panel switch "OFF", the unit will be in standby mode (drawing approximately 25mA). The panel switch indicator and 'TEMP' and 'BATT' LED should remain extinguished.
Connect and switch the load 'ON'. Red indicator on the panel switch will illuminate indicating that AC power has mow been applied to the load and the unit is operational. 'BATT' LED should remain extinguished, unless the battery is low. 'TEM' LED should also remain extinguished. The fan may operate depending on the ambient temperature inside the unit.
When the load is removed with the panel switch still 'ON', the indicator on the switch should remain illuminated indicating AC Power is still available at the socked. The unit will begin timing out before going into standby mode. After a few seconds the panel indicator will extinguish and the relay inside the unit will click. The warning buzzer will beep indicating that the unit is in standby mode.

Functions

Buzzer - The buzzer will sound when the battery voltage drops to 10.7 volts
'BATT' LED - The LED will flash when the battery voltage drops below 10.5 volts. The unit will switch 'OFF' the supply to the load and the LED will extinguish. The unit will automatically restart when the battery voltage exceeds 11.0 volts.
'TEMP' LED - The LED will illuminate to indicate that the unit has shutdown to protect itself against overheating. The unit will automatically restart after cooling and the LED will extinguish.

Made in Australia

Download this page in format.

Print friendly version of this page